Chip tuning for Bosch Smart System - SpeedBox 1.1

Tuning chip for electric bikes with Bosch 4th generation motors with Smart System. Enjoy riding without speed limits.

Product is sold out

Contact us for an alternative

A new tuning chip for your e-bike with 4th-generation Bosch motors featuring the Smart system. Enjoy riding without limits.

SpeedBox 1.1 for Bosch allows you to disable the speed limiter on e-bikes with the Smart system.

You can monitorreal-time data across the entire speed range while riding in the SpeedBox App—compatible with the SpeedBox 1.1 B.Tuning for Bosch—on your phone’s display.

How does SpeedBox 1.1 for Bosch work?

To properly activate all SpeedBox tuning functions, you must enter the menu after turning on your e-bike and select your e-bike’s battery capacity.

This product is also characterized by its ease of use. You can activate the SpeedBox 1.1 chip on the e-bike’s display. Do not activate the tuning while riding! After briefly activating the WALK function (by holding down the “-” button), the display will show 3.5 km/h (2.2 mph), and from that point on, you can ride at speeds up to 35 km/h. You can change the default speed limit to any value (up to 99 km/h), but to minimize the risk of error codes, we recommend not exceeding 35 km/h.

To deactivate the chip’s function, reactivate the WALK function (by holding down the “-” button). Do not deactivate the tuning while riding! The display will show 2.5 km/h (1.6 mph), and the 25 km/h speed limit will be re-enabled. The e-bike will then function the same as it did before the chip was installed.

We’ve also considered e-bikes that don’t have the WALK function available or active. In this case, you can activate and deactivate the tuning by switching back and forth between the two modes twice—that is, by pressing the - + - + button combination.

To set the maximum assist speed, cycle through the modes by switching down three levels from TURBO mode and then up three levels (eMTB – TOUR+ – ECO – TOUR+ – eMTB – TURBO). The current speed limit will then appear on the display. You can change the maximum assist speed by enabling or disabling the WALK function, or by rotating the wheel 360°. A reading of 2.5 km/h on the display corresponds to a limit of 25 km/h, 3.0 corresponds to a limit of 30 km/h, 3.5 corresponds to 35 km/h, and so on. The last displayed limit is saved after 15 seconds of inactivity.

After finishing your ride, leave the e-bike turned on until the display shows a steady 0.0 km/h. During this phase, the display will show the remaining time. You can then safely turn off the bike and look forward to your next ride.

Installation

We use original connectors in the production of SpeedBox chips to ensure that chip installation is truly simple and the wiring is correct. We’ve written detailed instructions and recorded videos so that every customer can install the SpeedBox on their own. Removing the tuning chip is just as easy as installing it. If you have any problems with the wiring, don’t hesitate to contact us.

If you’re planning to install the SpeedBox on a brand-new bike, you’ll need to ride at least 10 km on it before activating the chip for the first time.

Important

Connect the male and female connectors in the direction of the lock. Do not twist the connectors while connecting them!

Manual

Detailed installation instructions can be found here.

Warning

Please note that operating e-bikes modified in this way on public roads may violate the laws of certain countries. The manufacturer assumes no liability for damages resulting from the use of SpeedBox products. E-bikes equipped with SpeedBox products are not permitted for use on public roads, bike paths, or in public areas. E-bikes equipped with SpeedBox products may be used exclusively on your own property, at your own risk. Using SpeedBox products may void your e-bike’s warranty.

We recommend using additional safety features and protective gear to prevent injury.

We recommend that you do not update your e-bike’s firmware. Updating increases the risk of the tuning being detected.

Disable automatic updates in the Ebike Flow settings.

The warranty does not cover product malfunctions caused by a motor update.

During short stops, we recommend keeping one foot on the pedal to prevent the odometer from resetting.

During longer stops, allow at least a partial kilometer recalculation to complete.

Do not remove the display to lock the e-bike until the kilometer recalculation is complete.

Always activate or deactivate tuning while the bike is stopped, not while riding.

We recommend not exceeding the recommended maximum speed of 35 km/h.

Ebike Electronic s.r.o.

Ebike Electronic s.r.o. is the company behind the SpeedBox brand, one of the leading manufacturers of tuning chips for e-bikes. Since 2014, the company has specialized in the development and production of electronic solutions that expand the capabilities of modern e-bikes and give cyclists more freedom while riding. The products are designed with an emphasis on reliability, easy installation, and broad compatibility with various motor brands. SpeedBox was born out of a combination of a passion for cycling, technology, and the constant search for new possibilities.

Contact: Ebike Electronic s.r.o., Rybna 716/24, 110 00 Prague 1, Czech republic, e-mail: info@speedbox-tuning.com, phone: +420 702 042 874, website: www.speedbox-tuning.cz

 

 

Questions

Please fill in your contact details, enter your inquiry, and we'll get back to you as soon as possible.